Видео

I liked the part where he changed the motor

Hi my friend, thanks! What version of itdid you buy?

This video was my guide to install the new Android Radio for same car. I followed the instructions, noting that I did not install the rear camera as I don't really need it. Thanks a lot for this helpful guide.

Thanks, very well explained. LIKE!

Dein Link funktzioniert nicht mehr. Welches model ist das? Ich müchte fur meine Ibiza auch so was kaufen, danke.

Peltier 12706And between peltier12715 What is the diffrence

Hey.. how did you fixed the steering wheel controls not working ? Tyia

Dónde lo puedo comprar

What voltage to the LED? No need resistors? and why red and blue not blink at the same time at low frequency?

Hi, it was a good video thank you, i have a question that i want to ask about the slicer you are using, i installed ultimaker cura but did not found the printer anycubic mega pro, what should i do?

Я в микроволновку на разморозку ставлю

It works fine. Thank you! But I'm desperate, why do I have to go to the trouble of soldering this part to get it to work? Is it a bad design of the board?

Hi did you do the final bit where you screw the screen in

Salve il touch e in vetro o plastica ? con amplificatori suona bene ?

@Drxxx i get 3v on the usb port. it's able to power a low quality office mouse but im getting no data transfer, the pc wont respond to the mouse movement. What could i do if your able to help.

Hafıza tutmuyor ne yapmamız gerekiyor.

Do you know if this works in the 2015 seat Ibiza toca without the existing screen just a radio

1, il mandarino non va avvitato visto che non c'è filetto ed è conico 2, la rondella spaccata va posizionato verso il dado e non sulla testa del bullone (fissaggio porta pezzo)

Driving the LED directly without a resistor will only harm the op-amps on the FG output. Why do people do this?

I’ve just installed one of these unit but the issue I’m having is whenever i play something the sound only comes from the front two tweeters speakers. Do you know why. I’ve tried changing the settings but that didn’t work,

Hello, does the audio quality decrease in comparison with the original defaut autoradio?

I have just installed the radio everything works fine but I have no volume does anyone know what the issue is

tks a lot :)

which cabels are needed for the camera? ive tried the back lights one but it isnt shown in the video at 6:30 ? thanks a lot for the help!!! 🙏🏽🙏🏽

What if my ibiza model has hazard lights where the original head kit was? Its 2013 just not double DIN?

Am I the only one who can't decrease or increase volune via the handle left to the wheel?

how do you activate the steering wheel options (comands)?

thanks man ! it's very helpful, however can soleone tell le hiw to use apple car ? thank you in advance 😊

There are rubbish people.

Hi, fitted today and have a few questions if you could answer please: 1. My car is a seat and the can unit identify it as a VW, steering wheel controls do not work. Is there a connection for these? 2. Rear Camera distance lines are not shown, looked through all the settings which seem correct, can you advise? 3. I was looking to go into developer mode but it needs a password tried the one on the video and a few generic ones which are wrong, can you advise? 4. When I click on ‘video’ it plays sound with warning on the display saying ‘do not watch video while driving, I’m stationery and it will not show the video? I don’t see the menu on mine for the boot to change icon? Thanks

very helpful, thanks😉

Amazing video. Great job!!

Hi How can you remove the small plastic stuffs to get rid of the screw?

My project uses 40 of these USB shield. after solder the jumpers 5,5,3, then still about 20% will not work. no power gets to the USB port. HOWEVER I DISCOVERED A FIX. it works for me to simply BEND UP the USB PORT. I should be parallel to the board. Also when you insert the USB cable, then wiggle it and pull it out slightly. I have gotten all my Shields to work using this. I highly recommend you to purchase a USB voltage meter. with poor connection you can get only 2.6 v and it fools you.

hi. On the camera wires I connected the red one to the reverse gear wire and the black one to the minimum ground wire and on the radio I only connected the yellow connector. It doesn't work, the image appears with interference and nothing is seen. Any tips?. And great video

ware did you get the little crimper , nothing else works in that terminal block...

Hola podrías resolverme una pregunta conectando asi la radio no va directa a la bateria y la descarga es que al momento de apagarla nose si se apaga del todo o se queda en stand By… gracias por tu ayuda

Which one of the cables are for the reverse light? 6:27

You son of a wh0re why didn't you show the CANBUS cable going in ?

Thank you

If i disconnect the orange and red cable ny radio powers off. If i disconnect the other red orange cable which is connected with a red and black smaller cable ny radio doesn't turn off when i get my keys out. How do i need to fix this?

Alfuien tiene la contraeña de fabrica?

Where did you get the unit from?

Debería de apagarse la radio una vez apagas el coche y quitas el contacto??

Cool 👌🏻👌🏻👌🏻

do i have to install the rear camera looks complicated actually its just the wires that confuses me with the back camera the bit with the headlight and how you run the cables to the front or if there is already cables there you can use

Servus, wofür muss ich die Lichter hinten abstecken ? Ist das nicht illegal oder stecke ich die Lichter dann wieder an ? Weil damit dusconnecte ich ja wenn ich Bremse die Stopplichter oder kannst du das mir kurz erklären. Danke

mi radio es igual y no me detetecta los mandos del coche, que puedo hacer?

Did your volume buttons under steering wheels have any issues after instaling this?

Pour afficher une température de Référence: RF: Affichage de la valeur de référence: Appuyez sur le bouton de mesure 3 et alignez le pointeur laser avec cercle laser à 8 points 1 à l‘endroit dont la température servira de référence. La température s‘affiche alors à l‘écran 5. Maintenant, appuyez sur le bouton °C/°F/SET tout en maintenant le bouton de mesure 11 pour reprendre la valeur de température comme valeur de référence. Cette température est affichée sur l‘écran comme un indicateur de référence 6 à côté de l‘indicateur „REF“.